someone to help me solve this... P4 2.4ghz was upgraded to a P4 3.0ghz...

[rayfloyd_170]

---

mu boot ba diay ang P4 nga 3.0Ghz 800FSB sa mobo na 533FSB ra? hehehe galibog ko dah kay wako ka kBlo unsay mobo ani... kana tanan sa taas puro valid cause.. dako chance naa prob nag mem or ang temp sa procie basin taas wala nay thermal paste... basta p4 mga prescott init kaau..

[ditch_azeroth]

compatibility sa cpu-mobo ang most likely. also, i've seen cases nga wala na butangan ug tarong ug thermal paste nya maoy naka angil... basin kusog ra sad kaau mo init... in all likelihood, hirens boot cd is what you need to do diagnostics. one of my essential tools gyud ning cd-ha...

[azland]

wew! abi nako ikaw mupalit sa ako P4 3.0Ghz, wala naman ka ni txt pag sunday.. tabangan ta tka config ana imo board since d officialy supported ang 800 fsb cpu ana imo motherboard. i alread txted u about it katu nagsabot pa ta.

sorry sir wala na tika ma textsan kai nagdali ang ako manghud then kulang sa budget mangud. she really needs it that bad.. in anycase sir can you help me with it?

mu boot ba diay ang P4 nga 3.0Ghz 800FSB sa mobo na 533FSB ra? hehehe galibog ko dah kay wako ka kBlo unsay mobo ani... kana tanan sa taas puro valid cause.. dako chance naa prob nag mem or ang temp sa procie basin taas wala nay thermal paste... basta p4 mga prescott init kaau..

ang mobo aneh p4pex-te it supports up to 800 fsb.. as what sir werty said....

this is my mobo and im currently using it put back the old procie..

http://www.motherboard.cz/mb/asus/P4PE-XTE.htm

[parekoy]

or maybe wala magkacontact ang imo procie ug heatsink mao mo auto-shutdown.
it happens to me,
my remedy was putting aluminum material para naa lang sila contacts to each other,make sure also to put thermal paste para dili kaayo moinit.
solve na akoa problem after...

hope you try!!!

[wire]

@azland,

have u checked the heatsink from the newly installed proc? sometimes, this is our common mistakes, to not properly glued the heatsink into the proc. Try some gluing with "Silicon paste" that helps to absorb heat from you proc. When Proc is overheated, drastically, it gonna restart.

so try to check your heatsink & place it with what we called "Silicon Paste" on it.

i'm pretty sure this gonna solve your problem if supposing your mem & mobo are in good condition.

hi guys, im having trouble figuring out why my Newly upgraded cpu couldn't go through the OS. it only goes through the windows logo and processing then went out and shutsdown. i had to reboot it again then thesame happens... can anyone help me with this coz i need to use my PC ASAP.. thanks..

comments and suggestions needed badly..

[ERTM]

one thing lang ako suggest... since inamaw ni ako but effective... try to put 5pesos coin inserted between your procie and heatsink... before doing it, ba-id sa imo 5pesos nga mohamis ang surface... it's very effective...

[renz_slayer]

try to put aluminum foil bro, mga at least 4 folds para macontact jud ang imo procie and heatsink mao na ako gigamit sa una effective jud kaayo...

[death.groomer_88]

Hinumdumi lang bro na everytime imu i-remove ang heatsink, apply-i ug thermal paste balik. Let the heatsink flatten the thermal paste arun sure jhud na walay air spaces in between para magcontact ang duha. Mau man sad ni ang nahitabu naku.

[nash]

Check your bios version if it is the one that supports your new processor. According to the asus site, your board has limitations when using 800Mhz. It will only work if your ram is DDR400 and on the latest bios verion which is 1009.004. Please check the link below regarding this. Hope this helps.

ASUSTeK Computer Inc.-Support-

[azland]

actually mga ka istoryans, naka boot neh siya went through sa OS naka open pa ug folder after pila ka seconds ning shutdown dayun. what i have notice lack of power since a higher version of procie is inserted... sir nash is correct i have to check my bios version but all through out naka sulod man sa OS. non the less i'll still try your suggestions guys... thanks.. already talk to mr. werty about it..

anyone knows where to buy thermal paste?