Who knows how to overclock a E4500?

[poldopunk]

---

ok ra pero dili man gud na pareha ug reaction ang mga chips to voltage, pareha sa akoang E4500, kailangan pa ug 1.47 volts para stable at 3.2 GHz during stress-testing as compared to galen nga 3.5 GHz man siguro to at same voltage if i remember correctly.

[ArtVincent.Ph]

if u talking about the volts sir poldo...na 1.47 and differ in maximum performance....did2 na siya sa multiplier gi change? exactly..which part ninyo gi-change to 1.47 volts?

[poldopunk]

inig increase nimo sa frequency sa mga components, at some point the component will need additional voltage man para ma stable. ang processor voltage sa BIOS usually is VCore or CPU VID.

[sir_dakz03]

... excuse me?? Butt in lng ko ahp... Nag.himu gd kog thread kae naa sad ko problema sa akng BSEL mod... ask lng ko, para ma.change nako ang info sa thread: e7500 akng processor, akng gi BSEL mod para ang FSB from 1066Mhz, nahimug 1333MHz... kng mag.stability test ko, papawng xa (especially kng mag.benchmark nako sa games).. dapat pa ko mag vcore mod?? kae pag.log nako sa akng CPU-Z gd, ang pinaka taas nya na voltage at OC speed is 1.2546 at most... wa gane xa kaabot sa ceiling sa iyang stock na Voltage range which is
0.85V – 1.3625V
... so unxaon mani nako guyz para ma.stable jd xa karon, dili nako ma.sagunson ug full capacity load akng CPU since in about 15-30 mins of full CPU load, mapawng... pero ang voltage nya, stock ra jd... I dont seem to have the reason sa vcore mod since increasing the voltage also increases the CPU spees, dba help guyz...

[glide 1]

bro read this thread - all 3 pages. Poldo's and centax's advice is what you should follow. You will most likely need a volt mod aswell to get your procie stable.

copy paste nako diri kay pikas thread nako ni gi post -

sir_dakz03 - try to find a volt mod also for your procie. same ra na sa fsb mod but on different pins. Unsa na nga klase na mod? "shorting" pins or "isolating" type?

Usaully blue screens are ram related. Kalit ug pawong kay thermal or power rails from psu related (starved imong 12v, 5v, or 3.?v).

sa E4500 nako sa una kay shorting type, kuti sad. i-stabilize usa imo procie with the right voltage to go with your higher fsb. Watch for temps. Check ram timing kay mo saka pud na cya with the new higher fsb.

Unya na i-oc imo vc para ma pinpoint nimo kung ang proc, ram, or vc ang unstable.

Good luck

[sir_dakz03]

... kuya, ang ako ra jd option ani para ma.stable is ang vold mod/vcore mod ra jd. Akng BIOS, locked jd ang settings para ma.adjust ang steppigs. Gikan ra man gd ni sa set sa HP pavilion. Oo, nag.shorting ra ko, based sa pang 1333 na fsb mod...

... So dapat mag vol mod sad diay ko ani sa what do you think man ang corresponding na volt mod naa mae 1.4, 1.45, 1.5... asa man ko ani testingan nako tanan.. nya, I see, murag akng system is having problems adjusting to the mod AND is starved from its voltage... wew...

... stock ra ra ba akng gigamit na cooler ron, kae ang mga cooler sa intel, dili mu.sud sa akng motherboard, kae ang stock na cooler nya, naa man screws... ngita sa ta ko paagi para ma.tang2 ang para screw para maka butang ko ug bag.o na cooler...

... ara diay ang detalye sa akng system using cpu-z...

[raven007]

E4500 @3.5GHz overclocking using watercooling system