AutoCAD 2008 Thread

[turff_y]

---

@jinkazjinkaz: bcn nka ingon ka ana boss na revit ang uso karn kay ni fit ug useful kau sa imo work..
sa ako lng, ok ghapon ang autocad since its use is intended to fit any drafting work...and speaking about 3D autoCAD is one hell of a tool sad...

if AutoCAD = notepad and Revit = MS Word, dnt forget flexible kau ang notepad..and til now la jud ni gi tang2 sa windows kani na tool..
so, hope lets not make it a point na mg introduce ta ug lain na application dro na thread kay autocad man ato gi storyahan boss.

[i.draw.fast]

@turff_y:

bitaw, bai... depende raman sad gyud na pag-gamit nimo sa tool. kay unsa-on nalang kung naa kay auto pero dili ka kamao mudrive. di ba? same principle ra gihapon.

[mrxxxx]

ok ra ba eskwela autocad tesda and na ba assurance nga maka ad2 gwas....pila ka years of experience sa autocad before ma ka ad2 abroad?unsa mga country demand inhi.

[turff_y]

ok ra ba eskwela autocad tesda and na ba assurance nga maka ad2 gwas....pila ka years of experience sa autocad before ma ka ad2 abroad?unsa mga country demand inhi.

i wud say ok..magamit jud nuon nimo kay ng try apply2 lng gud para kasuway ko interview foreign employer, gpangitaan jud ko ug certification..bsan na prove nko kabalo ko sa autocad..if certification ra imo kailangan, better enroll sa tesda kay tesda-cite man na na program..mas credible jud kaysa lain..though murag 2002 man cguro na version pero di man necessary na updated version jud kay mahal man sad palit nila sa license..naka study nko for 40hrs about 2 months jud..maka ingon jud ko na maski kabalo nko but naa pa jud d ay kay la nakat-unan if dili ka skwela(pwera nlang if mau laki jud ka..pero di man ko maung laki..hehe)

[mrxxxx]

i wud say ok..magamit jud nuon nimo kay ng try apply2 lng gud para kasuway ko interview foreign employer, gpangitaan jud ko ug certification..bsan na prove nko kabalo ko sa autocad..if certification ra imo kailangan, better enroll sa tesda kay tesda-cite man na na program..mas credible jud kaysa lain..though murag 2002 man cguro na version pero di man necessary na updated version jud kay mahal man sad palit nila sa license..naka study nko for 40hrs about 2 months jud..maka ingon jud ko na maski kabalo nko but naa pa jud d ay kay la nakat-unan if dili ka skwela(pwera nlang if mau laki jud ka..pero di man ko maung laki..hehe)

sa main man ? ok ra ba did2 ilang training ..unsa country nag demand ani

[TCV915]

im starting this thread for a place to ask questions and give tips and tricks about AutoCAD 2008

let me start with my question

in 2008 when i use force snapping i press shift+right click then "E" for endpoint of a line, in the old version you could do this then without letting go of the shift key ,transfer to another snap like say "M" for midpoint.
in 2008 however i have to press shift+right click E for endpoint,then you have to let go and shift-right click again then M for midpoint

is there any setting i can configure to make it like the lower versions??

one thing you must remember when installing new versions of Cad is the Migrate Option.
if you install newer versions, install it first before removing the older version which has all your
prefered/configured settings.
then at first run sa imong newer version, there is a pop out to let you Migrate all settings
from your older version..click "Migrate" then all your settings from the previous versions will
be copied to your newer version...

as to snapping issue... you dont need to type M, E, etc for Midpoint, End respectively
once you have set it to check most snap points...
imo lang ipa dool imong pointer and it will snap on endpoints, midpoints, etc once
you have this setting...
below is my screenshot of this setting and i hope this will help you a bit...

[mrxxxx]

mo accept ba uban compaby kung autocad graduate ka sa tesda ..week raman ilang training?

[turff_y]

one thing you must remember when installing new versions of Cad is the Migrate Option.
if you install newer versions, install it first before removing the older version which has all your
prefered/configured settings.
then at first run sa imong newer version, there is a pop out to let you Migrate all settings
from your older version..click "Migrate" then all your settings from the previous versions will
be copied to your newer version...

as to snapping issue... you dont need to type M, E, etc for Midpoint, End respectively
once you have set it to check most snap points...
imo lang ipa dool imong pointer and it will snap on endpoints, midpoints, etc once
you have this setting...
below is my screenshot of this setting and i hope this will help you a bit...

sakto ka bro, right-click ra settings sa tab as shown..mao sad nka nindot sa feature sa newer versions kay minimize na typing the commands,tho, somtyms necessary lng ghapn..

[turff_y]

mo accept ba uban compaby kung autocad graduate ka sa tesda ..week raman ilang training?

depende raman na sa company bai..i think first gpangita sa company is ang imong skill...supporting paper raman cguro ang certificate of training..ma justify man sad na nimo during interview..so dili ra big deal if asa ka ngskela..altho naa cguro uban company..its a plus jud if accredited jud ang skul..

[mrxxxx]

so mo prefer gud ni cla sa computer graduate? tinuod ni demand ni autocad sa dubai? or na pa lain country nga nag demand ani?