Fibre glass reinforced, 1 1/4" cut off wheels/disc for dremel/rotary tools 10pcs for 250php

[titaniumbox]

---

TTP223B Digital Touch Sensor capacitive touch switch module for Arduino at 375.00php

Description:
The module is based on a touch-sensing IC (TTP223B) capacitive touch switch module. In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode.

Features:
Low power consumption
Power supply for 2 ~ 5.5V DC
Can replace the traditional touch of a button
Four M2 screws positioning holes for easy installation

Specification:
Item
Power supply voltage VCC: Typ 2.0V Max 3V
Output high VOH: Typ 0.8VCC
Output low VOL: Max 0.3VCC
Output Pin Sink Current(at VCC=3V,VOL=0.6V): Typ 8mA
Output pin pull-up current(at VCC=3V,VOH=2.4V) : Typ 4mA
Response time (low power mode) : Max 220mS
Response time (touch mode): Max 60mS
Size: 24x24x7.2 mm
Weight: Typ 2g

Package Included:
1* Digital Touch Sensor capacitive touch switch module for Arduino

Spoiler! 

[titaniumbox]

30ft Wireless Bluetooth RF Transceiver Module serial RS232 TTL for arduino

Description:
TTL data transparent transfer between a host Bluetooth device.
Module HC-06 master and slave, two in one.
Build-in CSR company Bluetooth chip BC417143.
Bluetooth specification v2.0 + EDR.
Works with any USB Bluetooth adapters.
Default Baud Rate: 9600,8,1,n.
Coverage up to 30ft.
Built in antenna.
Mini Size.

Specifications:
Power input: +3.3VDC.
Signal coverage: 30ft
Size: 26.9mm×13mm×2.2 mm
Weight: 1g

Package Content:
1*Wireless Bluetooth RF Transceiver Module

Spoiler! 

[titaniumbox]

HC-06 HC06 Wireless Serial 4 Pin Bluetooth RF Transceiver Module HC-06 RS232 With backplane

Specification:
It's HC-06 HC06 bluetooth module.
Allows your device to both send or receive the TTL data via Bluetooth technology without connecting a serial cable to your computer.
Works with any USB Bluetooth adapters.
Default Baud Rate: 9600,8,1,n.
Built in antenna.
Coverage up to 30ft.
Bluetooth version: V2.0+EDR
Operating voltage: 3.3V
Default Baud Rate: 9600,8,1,n.
Signal coverage: 30ft
Cable length: 21.5cm
Item size: 4.3 * 1.6 * 0.7cm
Item weight: 3g
Package size: 9 * 3 * 1cm
Package weight: 8g

Commercial Series: Bluetooth module board Series

With LED indicator light, use 150mA and 3.3V regulation chip.
With VCC、GND、TXD、RXD foot for the Bluetooth
With "Re-search" button(ON/OFF/WAKE foot for it , external MCU out input "High level" can control module to re-search)
Compatible with bluetooth master module"、slave module"or master-slave(whole) module.
Input voltage: 3.3~6V
Size: 1.55cm*3.98cm

Note:
Input power supply 3.3~6V, Prohibit more than 7V
No "Automatically prevent power supply reversing func", so please correctly connect power supply
We advise to install "Bluetooth master module"
The "State" is output foot for LED status, when bluetooth "Unconnected", output "Pulse" ; when bluetooth "connected", output "High level", we can determine the states from "MCU"
If only the board , No any "Bluetooth Function "

Package Content:
1PCS*4Pin bluetooth module HC-06 with backboard
4PCS*Free dupont cables.

Spoiler! 

[titaniumbox]

MAX7219 Dot led matrix module MCU control LED Display module for Arduino at 450.00php

Item Description:

Module parameters:
1. A single module can drive an 8 * 8 common cathode lattice
2. Module Operating voltage: 5V.
3. Module size: 5 cm long X 3.2 cm wide X 1.5 cm high
4. With four screws hole, aperture 3mm, by using our M3 Tongzhu fixed
5. Module with input and output interfaces, supports multiple modules cascade
6. Led colour: Red

Wiring instructions:
1. The module left as an input port to the output port on the right.
2. The control of a single module, simply input port to the CPU
3. Multiple modules cascade input termination CPU, 2 output termination module, a module of the input of the input terminal, the output terminal of the first two modules of the first three modules, and so on ...
51 MCU, for example:
VCC → 5V
GND → GND
DIN → P22
CS → P21
CLK → P20

Package contents:
1* MAX7219 Dot led matrix module
3pcs Dupont wire

Spoiler! 

[titaniumbox]

Micro SD Storage Board Micro SD TF Card Memory Shield Module SPI For Arduino at 375.00php

Specification:
The module (MicroSD Card Adapter) is a Micro SD card reader module, and the SPI interface via the file system driver, microcontroller system to complete the MicroSD card read and write files. Arduino users can directly use the Arduino IDE comes with an SD card to complete the library card initialization and read-write

Module features are as follows:
1. Support Micro SD Card, Micro SDHC card (high-speed card)
2. The level conversion circuit board that can interface level is 5V or 3.3V
3. Power supply is 4.5V ~ 5.5V, 3.3V voltage regulator circuit board
4. Communication interface is a standard SPI interface
5. 4 M2 screw positioning holes for easy installation

Control Interface: A total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin;

3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply;

Level conversion circuit: Micro SD card into the direction of signals into 3.3V, MicroSD card toward the direction of the control interface MISO signal is also converted to 3.3V, general AVR microcontroller system can read the signal;

Micro SD card connector: yes since the bomb deck for easy card insertion and removal.

Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm, the module is easy to install positioning, to achieve inter-module combination;

Shipping Included:
1*Micro SD TF Card Shield Expansion Board for Arduino DIY

Spoiler! 

[titaniumbox]

5V One 1 Channel Relay Module Board Shield For PIC AVR DSP ARM MCU Arduino

Specification:
5V 1-Channel Relay interface board, and each one needs 15-20mA Driver Current
Equipped with high-current relay, AC250V 10A ; DC30V 10A
Standard interface that can be controlled directly by microcontroller ,such as Arduino , 8051, AVR, PIC, DSP, ARM and so on
Contact independent wiring, safe and reliable
With screw holes for easy installation
Size:4.7 x 2.9 x 1.8cm

Package Included:
1PCS*5V Eight 1 Channel Relay Module For PIC AVR DSP ARM Arduino

Spoiler! 

[Inta]

asa sad nato mapalit imong items bro?

[titaniumbox]

asa sad nato mapalit imong items bro?

you got PM bro

[titaniumbox]

Stepper Motor Drive Controller Board Module L298N Dual H Bridge DC For Arduino at 375.00php

Specification:
1. Using L298N made by ST company as the control chip, the module has such characteristics as strong driving
ability, low calorific value and strong anti-interference ability.
2. This module can use built-in 78M05 for electric work via a driving power supply part. But to avoid the damage
of the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage.
3. Using large capacity filter capacitor, this module can follow current to protect diodes, and improve the reliability

Specification:
1. Double H bridge drive
2. Chip L298N (ST NEW)
3. Logical voltage 5V
4. Drive voltage 5V-35V
5. Logical current 0mA-36mA
6. Drive current 2A(MAX single bridge)
7. Storage temperature -20 to +135
8. Max power 25W
9. Weight 30g
10. Size:43*43*27mm

This module is integrated with a built-in 5V power. When the drive voltage is 7V-35V,
it can enable the onboard 5V logic power supply; after the power supply, don't input
voltage in the interface+5V power supply, but you can lead the 5V for external use.
when ENA enable IN1 IN2 control OUT1 OUT2
when ENB enable IN3 IN4 control OUT3 OUT4

Package Content:
1* Stepper Motor Drive Controller Board Module L298N Dual H Bridge

Spoiler! 

[titaniumbox]

FT232RL USB to Serial adapter module USB TO RS232 Max232

Specification:
Use FT232RL chip;
Draw out all signal port of FT232RL chip;
RXD/TXD transceiver communication indicator;
USB power supply, can choose 5V or 3.3V ,set by jumper.
Each module has been tested
Can use for Arduino Pro Min.

Shipping Included:
1PCS*FT232RL USB to Serial adapter module USB TO RS232 Max232 for Arduino download

Spoiler!