BEST ASSEMBLER IN CEBU

[dubioz]

---

Upgrade ra man gud lestat, so barato'g gawas:

Pentium D 2.66 Ghz: P6,950.00

PQI 512 MB DDR2 Memory: P1,950.00

Dynamo 500W power supply with SATA connector 2 fans: P1,200.00

Samsung SATA drive kay usa ra IDE connector ang motherboard: P2,900.00

D945 GTPL Motherboard: P5,250.00

Grand total: P18,250.00

Hmmm... Karon na gi add nako tanan, mahal man diay!

Still using my old DVD drive and CD-RW drive and computer casing.[br]Date Posted: May 26, 2006, 07:40:26 AM_________________________________________________K adto akong gi reklamo, lain to na setup. 3 Ghz single core but 64bit. Mas mahal pa to.

[EarlZ]

with your PSU i doubt you can overclock well, actually bro your motherboard is not a problem is that motherboard is rated to run 200Mhz FSB, the D805 has a stock of a mere 133FSB, im pretty sure you can run it at 166fsb resulting on a 3.3Ghz dual core. with proper cooling ang voltages you might even be lucky to reach 4.0Ghz

[bim27142]

Who's the best assembler in Cebu? I recently had my x64 PC assembled by a "name" assembler and was very dissatisfied. My biggest complaints:

1. Didn't install the correct power supply.

2. Didn't connect the front audio panel.

3. Didn't install enough fans.

4. Used the WRONG kind of fan.

What assembler gets these all right?

comments -

1 - under power or dili ATX gi gamit hehehe
2 - if generic cases, don't bother...
3 - personal preference naman ni tingali...
4 - hhhmmmmm... para asa jud diay unta na fan?

i used to hear these words before from an old teacher " if you want to get the job done, you do it yourself... "

[lestat1116]

best computer shop dri sa cebu?

[dubioz]

1. Under power. Kulang ug standby wattage. Dili mo boot from standby ang pc.

2. Generic case, but I was able to connect the audio panel myself correctly. Works perfectly now. Dili na mo reklamo ang misis kung mo duwa ko'g FarCry 64 bit.

3. Dili personal preference, kay pati mobo ni require ug 3 fans. Pwede duha basta kadton'g dako na fan.

4. Kinahanglan gyud ug fan na controllable by mobo, kay sige'g overheat kung dili.

Who's the best assembler in Cebu? I recently had my x64 PC assembled by a "name" assembler and was very dissatisfied. My biggest complaints:

1. Didn't install the correct power supply.

2. Didn't connect the front audio panel.

3. Didn't install enough fans.

4. Used the WRONG kind of fan.

What assembler gets these all right?

comments -

1 - under power or dili ATX gi gamit hehehe
2 - if generic cases, don't bother...
3 - personal preference naman ni tingali...
4 - hhhmmmmm... para asa jud diay unta na fan?

i used to hear these words before from an old teacher " if you want to get the job done, you do it yourself... "

[dubioz]

Follow na lang the advice of dagget and werty, and assemble yourself. Na kat-on nuon ko'g assemble tungod sa daghan sayop sa assembler.

1. Under power. Kulang ug standby wattage. Dili mo boot from standby ang pc.

2. Generic case, but I was able to connect the audio panel myself correctly. Works perfectly now. Dili na mo reklamo ang misis kung mo duwa ko'g FarCry 64 bit.

3. Dili personal preference, kay pati mobo ni require ug 3 fans. Pwede duha basta kadton'g dako na fan.

4. Kinahanglan gyud ug fan na controllable by mobo, kay sige'g overheat kung dili.

Who's the best assembler in Cebu? I recently had my x64 PC assembled by a "name" assembler and was very dissatisfied. My biggest complaints:

1. Didn't install the correct power supply.

2. Didn't connect the front audio panel.

3. Didn't install enough fans.

4. Used the WRONG kind of fan.

What assembler gets these all right?

comments -

1 - under power or dili ATX gi gamit hehehe
2 - if generic cases, don't bother...
3 - personal preference naman ni tingali...
4 - hhhmmmmm... para asa jud diay unta na fan?

i used to hear these words before from an old teacher " if you want to get the job done, you do it yourself... "

best computer shop dri sa cebu?

[lestat1116]

pero unsa man jud best computer shop para maka palit og parts?

[EarlZ]

pero unsa man jud best computer shop para maka palit og parts?

Kung sikat nga retail id prefer mo kuha sa sa insotec

[dark_humbz]

For me, there is no such as BEST assembler, everyone will commit mistakes once in a while...

[dubioz]

Agreed. But, don't you think a responsible assembler would have informed him/her/itself at least about the new power requirements to run the newer mobos and processors? After I found out that the power supply was not the right one for my board, my assembler resisted replacing it at first, saying that all their power supplies are like that. It was only later that they admitted their mistake. Seems to me they simply DID NOT KNOW that power requirements for the new boards are different.

For me, there is no such as BEST assembler, everyone will commit mistakes once in a while...