Video Card or Motherboard Problem??

[waterboy0911]

---

HSF bay wala na matarong ug taod.. ni agi nana.. tang tanga na bro.. then i balik..

[personalmgt]

Okay, as the guy who installed his new Core Contact Freezer, I have to do some input/report about it. We come into theories that it could be the Cooler that's the culprit because the malfunctioning started a week after I installed the cooler. But then I doubt this theory, as I know I did well in that work. Even though I already enjoyed the payment that rhodem24 gave me, I worry about the stuff that I work at that goes kaput.

I talked to the OP about the problem ever since I installed the Core Contact Freezer. He had his PSU replaced once or twice before the Cooler was added. When I added the Cooler, I took some things into consideration like how well should I spread the Thermal Paste. As experienced on the old P4 processors, I used to assemble these rigs long ago with the thermal paste to be spread separately. I know how much Thermal Paste you should put in the HSF and im sure I have placed enough Thermal Paste on it.

As of the theory that the HSF could be too loose, I doubt it. Before OP's temps was this high, OP reported to me that the temps went lower than the typical temps with the stock HSF added. If the cooler was loose that it didn't make contact with the processor, the temps would be ridiculously high, more likely 50% more heat. But OP did not get any weird high temps. Finally, I nearly broke my thumb just to hear that "snap" sound so I could confirm that the cooler is tight with the processor.

If you check his previous thread about the weird temps, you can see that his temps was 60c high. As far as I can predict, he took the screenshot at noontime which is the hottest part of the day. But then as you see this, he still had the same temps at the same time which is noontime.

I'm not saying na pang-hugas kamay ni. What i'm saying is that this is my report that people could diagnose what really is the problem. Feel free to bash around this post, as I will welcome it

[centax error]

what's up with the fans 603 rpm? at that temps it should be spinning at max

[dmelsie]

if ako pa istoryahon mobo nay problema ana bai
try lain mobo to imoha videocard then burn test if mo occor ba ingana nga prob
kapila nako ka suway ingana na prob mobo naay daot
kay if e observe sad murag abnormal ang voltage nga ma sense sa mobo hasta ang rpm sa fan murag clue na ni nga nay defect imoha mobo usually tagsa ra dili magka dimao na sila nga sensors

[rhodem24]

@TS, have you tried the on-board video lang sa bro?? as what others here are suggesting... any kalambuan?

wala man on-board video akng mobo bro...

Maka hibong man dyud na nga voltage, 2vs1 asa kahay tinood anang tulo. Try to check sa bios bro kung unsay tinood voltage sa imong 12V. Kay ang uban voltage halos pariho raman.

I've checked sa BIOS, and its 12.xx... so, mura'g ang Everest nga readings mao'y sakto..

HSF bay wala na matarong ug taod.. ni agi nana.. tang tanga na bro.. then i balik..

Okay ra man ang HSF. dili siya mao ang cause kay gipa tang2x nako ni tanan sa shop then gipa assemble balik tanan... then ni balik man lang gihapon...

@personalmgt - hahahahaha sure ko dili ang HSF ani chan uy...

what's up with the fans 603 rpm? at that temps it should be spinning at max

I think ang sa pag set to sa BIOS sa min Fan speed.. akng gi adjust to 75% karon..

if ako pa istoryahon mobo nay problema ana bai
try lain mobo to imoha videocard then burn test if mo occor ba ingana nga prob
kapila nako ka suway ingana na prob mobo naay daot
kay if e observe sad murag abnormal ang voltage nga ma sense sa mobo hasta ang rpm sa fan murag clue na ni nga nay defect imoha mobo usually tagsa ra dili magka dimao na sila nga sensors

wala man ko'y ka suwayan para testing gud... mao na much better if pa ilisan nako'g bago ang mobo ug ang vid.card. hehehe.