Page 2 of 2 FirstFirst 12
Results 11 to 17 of 17
  1. #11

    bro try daw clean again ang memory niya, naka try ko ani pod, 30m - 1 hr then gi change nko mem kay na ok cya, considering nga nag reformat ka (new OS installation).

    unsa usually gigamit nimo nga ma notice nimo maka restart sa PC?

    try daw new reformat then ang e load kay OS, OFFICE, DRIVERS, then IE or GOOGLE CHROME, JAVA, FLASH, then try gamit ug FB if mo restart/ off ba cya. if mag isolate ko mao ni some few steps ako buhaton. then na discover nako memory problem. im using generic PSU sa ato nga PC.

  2. #12
    Check pd imung cooling source sa MOBO sir..

  3. #13
    Good day Sir!

    Dili sad sa pagpinamay pero ilisdi daw ang motherboard...dli na guro accurate ang pagdistribute ana sa power gikan sa supply mao murestart. Hope nga maayu nana

  4. #14
    Quote Originally Posted by rOck90's View Post

    Specs:
    (Combo ni pag palit 2nd hand, cheap, mao ako d palit walay 3mins na testing.LOL)
    Intel Pentium 2160 (stock speed)
    ECS P4M890T-M V2.0 (Pentium 2160 not supported CPU) but the original owner used this rig for many years.
    1X2GB Kingston DDR800

    added:
    Civo 600W PSU - brand new
    80GB WD SATA
    Samsung DVDwriter SATA

    Problem:

    #Reformat , OS installation, drivers ok ra ang unit..everything looks perfect. But anything after an hour or less,

    mag start na xa ug restart. Once mag start na xa ug restart, mag cge nalang balik2x ug restart, even dd2 rko sa BIOS, mo

    restart lang gypn. Sa cge na xa balik2x ug restart, wa na xa display (monitor), WEIRD kay ga normal beep lang gyapon xa.

    Ako d try ug gamitan ug VC, basin On-board video faulty. mao lang gypn mag restart. Pero after 3hrs naka power off/unplug,

    ok napud ng unit... but mao lagi mo restart after an hour or less than an hour. Basta duol sa 1hr ug usahay lapaw gamay.



    akong d himo na troubleshooting....


    --> 1) Overheating?? --- ako d gamitan ug stability test (AIDA 64) for an hour, ok man no problem..But after ani.na ako ng

    d stop... mga 15mins nag start na nasad ug restart. Once mag restart ni xa mag cge nalang balik2x even dd2 rko sa BIOS, mo

    restart ra gyapon.

    -->ako pd d try ug tan-aw sa BIOS after xa mag restart sa Hardware Monitor - Ok rman ang CPU temperature mga 40C+

    -->pag cge2 na ug restart ako pd d try ug hikap ang HSF sa CPU , HS sa northbridge wa man ga init.

    2) Change memory -- ako d try ug lain na DDR533 memory na 1GB, mao lang gypn mo restart after or less than an hour.


    3) Headers & SATA cables ako d isolate mao lang gypon resulta.

    4) CLR CMOS, tang2 battery, default BIOS settings - mao ra gypon resulta.

    5) ako pd xa d try ug gamit VC brand new Sparkle 7200GS 256MB (old stock ako na palit, but sealed pa). Mao gypn

    resulta.

    Ang wa nko ma try ug saksak/swap/testing sa lain nga unit ang PSU, mobo, ug processor.
    1. e swap og lain psu. kunh 2nd hand pana imong psu. basin ning bigay na tungod kadugayun. specially sa mga generic psu. gud for 5 years rana.

    2. worst case scenario, nay bad transistor or blown out capacitors sa imong board.

  5. #15
    up ta ani.. nindot mga comments

  6. #16
    yup. murag imo najud na mobo bro.

  7. #17
    either of the 3

    ECS P4M890T-M V2.0 (Pentium 2160 not supported CPU) but the original owner used this rig for many years.

    1X2GB Kingston DDR800

    Civo 600W PSU - brand new

    check for bulging capacitors or burns

  8.    Advertisement

Page 2 of 2 FirstFirst 12

Similar Threads

 
  1. My computer restart after installing deep freeze..HELP!!!
    By drei08 in forum Computer Hardware
    Replies: 19
    Last Post: 02-05-2013, 04:42 PM
  2. Computer Restarts After Shutting Down!
    By Techfinder in forum Computer Hardware
    Replies: 13
    Last Post: 12-13-2007, 10:39 AM
  3. pls. help yahoo messenger will not launch after installing it
    By princecrobz in forum Software & Games (Old)
    Replies: 6
    Last Post: 12-04-2007, 04:07 PM
  4. shutdown command restart ang action pls help
    By rcm0722 in forum Computer Hardware
    Replies: 6
    Last Post: 10-19-2007, 07:34 AM
  5. Cannot view my workgroup computers... pls. help
    By chercomengineer in forum Networking & Internet
    Replies: 15
    Last Post: 12-07-2006, 09:42 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
about us
We are the first Cebu Online Media.

iSTORYA.NET is Cebu's Biggest, Southern Philippines' Most Active, and the Philippines' Strongest Online Community!
follow us
#top