Need help on my DIY c02 tank (planted aquarium)

[tonioyantao]

---

pwede raman as long as you know that dili siya hupas.



yes sir. hehehe salamat sa pagtabang gihapon bisan wala naka sa planted.



ok rana, as long as dili permanent nga bara.

hehehe. wala lang lingaw lingaw ra nako.

[SeptemberII]

awa nnyo mga sir, nag himo ko ug bago na mixture gahapon...


no foam and bubbles on the c02 bottle pero sa pikas bottle with water naay mo gawas nga mga buwa



ang akoang diffuser sir murag naay mga buwa sa sides ug sa ubos. mao ba ni ang c02?


confused gyud kaayo ko run

[SeptemberII]

ani nalang para maka sigurado ka kung buhi imong gipalit na yeast. make this, in a bowl add 1 tsp yeast 2 tbsp sugar and half a cup of tap water it could be slightly warmer BODY TEMPERATURE NEVER BOILING!!!. stir until dissolve and wait for 30 mins. foam will rise bubbles will be present then your yeast is definitely alive. so the problem will be the obvious leak on the bottle cap where the tube is conected.

awa sir akoang gi follow imong gi ingun...
mura siya ug nag create ug foam


mura gyud ug cake ni burot oe. hahahaha pero akong diy c02 tank tawn

[tonioyantao]

pirting bulaa hehehe. well there you go. proof your yeast is very alive.

nay gamay bubbles sa 2nd bottle right? from the looks of it the bottle caps where the tubes are connected looks flimsy. the glue gun can only do so much but its never the right material for sealing especially sealing where pressure is involved.

your mixture is fine it's just the bottle.

[SeptemberII]

pirting bulaa hehehe. well there you go. proof your yeast is very alive.

nay gamay bubbles sa 2nd bottle right? from the looks of it the bottle caps where the tubes are connected looks flimsy. the glue gun can only do so much but its never the right material for sealing especially sealing where pressure is involved.

your mixture is fine it's just the bottle.

sir kani sa akoang diffuser nga picture sa taas ba, mao na ba na siya ang c02 bubbles ni pilit sa sides sa diffuser?

unsa akong buhaton sa bottles sir?

[tonioyantao]

you need to apply new sealant like epoxy. use a lot of it.leave it let it cure for a minimum of 2 days to make sure it's harden enough

mga tao ngara kinsa naka suway ug sillicone sealant? will it work with plastics?

[SeptemberII]

Salamat kaayo sir! Mag himo ko run ug bago na diy tank then i will use epoxy aron maka abot najud sa diffuser. I will update nya sir if palpak nasad haha

Btw, C02 bubbles ni ang nasa kilid sa diffuser?

[BelindaZachary]

basig naay leak TS, usa sad raba na sa rason nganu dili mo bubbles...

[SeptemberII]

basig naay leak TS, usa sad raba na sa rason nganu dili mo bubbles...

^Tanawa ang pic sa ako diffuser sir, c02 ba na siya naa sa kilid sa takob?
Mao sad lagi. Basin naay leak ba. Akoa nlng ni usbon gamitan ug epoxy aron dili mag hungaw. Feel nako hungae kay pag squeeze nako sa c02 bottle ni tingog man. Ni ssssshhhhh. Hahahaahaha hungaw jd ni.

Sir, okay ra ba nga ang diffuser ug hose naay tubig sa sud? Murag nay ni bara gud. Basin mao sad ni rason ba ngano d kaabot ang bubbles. Mao mangutana nlng ko nnyo mga master ^^

[ragingtakyo]

Nindot ni imo lingaw bai dah! post nya ug succesful na...hahahaha.